Paint Coating and Printing Ink Testing Instruments

Product Details:

"TQC" Micrometer Film Applicators

Adjustable Micrometer Film Applicator with stainless steel blade, aluminum frame and chrome thimbles and barrels.

The detachable blade makes cleaning easy. Also, this Micrometer Film Applicator isn’t supplied with springs which can break, rust or get clogged.

• Micrometric film applicator 75 mm wide
• Micrometric film applicator 100mm wide
• Micrometric film applicator 150mm wide
• Micrometric film applicator 200mm wide

Product Details:

The K Hand Coater provides a simple but
effective means of applying paints, printing inks,
lacquers, adhesives and other surface coatings
onto many substrates including paper, board,
plastic films, foils, metal plates, glass plates,
wood etc. Two or more coatings can be applied
side-by-side in a single operation making the
system ideal for comparing products.
MAIN FEATURES
Simple, economical.
Will deposit from 4 to 500 micron wet film thickness.
Good repeatability with special impression bed.
Stainless steel rods and wire used for K Bars.
K Bars are numbered and colour coded.
Two or more products coated simultaneously for comparison.

K BAR COATING
Wired K Bars are produced by winding precision drawn
stainless steel wire onto a stainless steel rod resulting in a
pattern of identically shaped grooves. These grooves
precisely control the wet film thickness. Close wound bars
will produce coating thicknesses from 4 to 120µm. Still
higher coating weights up to 500µm can be obtained using
open wound bars.

Special K Bars to apply intermediate wet film deposits are
manufactured to customer requirements. We stock wire
diameters giving the choice of the following deposits
(microns) when close wound.
4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28, 30, 32, 34, 36,
38, 40, 42, 44, 46, 48, 50, 52, 54, 56, 58, 60, 62, 64, 66, 68,
70, 72, 76, 80, 84, 88, 90, 92, 96, 100, 104, 108, 110, 112,
116, 120, 128, 130, 140, 150.
We also manufacture both wired metering bars and plain
smoothing bars to fit all laboratory and production width
coaters

Small Starter Set
1 small impression bed (coating area 11x18cm)
Supplied with 8 short K Bars Nos. 1-8 unless specified otherwise
1 short cleaning/storage rack
500 sheets proofing paper 12x21cm

Large Starter Set
1 large impression bed (coating area 22x34cm)
Supplied with 8 long K Bars Nos. 1-8 unless specified otherwise
1 long cleaning/storage rack
500 sheets proofing paper 18x31cm

Product Details:

"TQC" 4- Sided Film Applicators

The TQC 4-Sided Film Applicator (Quadruplex) has four application sides for applying paint films with four different predefined thicknesses, in film width 60 or 80 mm. One side of the applicator is supplied with a guidance support for straight application. This support may be removed as well. The high grade stainless steel will not be affected by acid or base elements.

Features:

• TQC Film Applicator (Quadruplex) width 60mm, four gaps, size on request.Max. gap size: 3000µm
• TQC Film Applicator (Quadruplex) width 60mm, gaps 15, 30, 60 and 90 µm.
• TQC Film Applicator (Quadruplex) width 60mm, gaps 30, 60, 90 and 120 µm.
• TQC Film Applicator (Quadruplex) width 60mm, gaps 50, 100, 150 and 200 µm.
• TQC Film Applicator (Quadruplex) width 80mm, four gaps, size on request. Max. gap size: 3000µm
• TQC Film Applicator (Quadruplex) width 80mm, gaps 15, 30, 60 and 90 µm.
• TQC Film Applicator (Quadruplex) width 80mm, gaps 30, 60, 90 and 120 µm.
• TQC Film Applicator (Quadruplex) width 80mm, gaps 50, 100, 150 and 200 µm.

Product Details:

"TQC" Baker Film Applicators

Cylindrical film applicator with 4 application sides for applicating paint-films of 4 different pre-defined thicknesses. The Baker applicator’s are available in film width 60 mm and 80 mm and are suitable for applying a host of different products onto flat and relatively solid substrates. Since it’s made out of high-grade stainless steel, the Baker Film Applicator will not be affected by acid or base elements.

 

Features:

• Baker applicator 60mm, 15/30/60/90µm or 30/60/90/120µm or 50/100/150/200µm
• Baker film applicator 80mm, 15/30/60/90µm or 30/60/90/120µm or 50/100/150/200µm
• Baker film applicator width 60mm, 4 gaps as desired Max. gap size 3000µm
• Baker film applicator width 80mm, 4 gaps as desired Max. gap size: 3000µm
• Baker film applicator width 80mm, 2x90µm / 2x150µm
  (special diameter: 18mm instead of 27mm)
• Baker film applicator width 100mm, 4 gaps as desired
• Baker film applicator width 100mm, gaps 15/30/60/90µm or 30/60/90120µm or 50/100/150/200µm
• Baker film applicator width 150mm, 4 gaps as desired Max. gap size: 3000µm
• Baker film applicator width 150mm, gaps 15/30/60/90µm or 30/60/90120µm or 50/100/150/200µm

Product Details:

Cross Cut Adhesion Test Kit CC3000

The TQC Cross Cut Adhesion Test KIT CC3000 is used to test the adhesion of dry coats of paint on their substrate by means of a series of cuts through the coating. Two series of parallel cuts cross angled to each other to obtain a pattern of 25 or 100 similar squares. The ruled area is evaluated by using a table chart after a short treatment with a stiff brush, or adhesive tape for hard substrates.

The cutting depth of the TQC Cross Cut Adhesion Test KIT CC3000 can be adjusted while the cutter is guided by two ball bearings to assure reproducible results. The depth of the TQC Cross Cut Adhesion Test KIT CC3000 is adjustable to measure coatings up to 250 µm thick.

Each TQC Cross Cut Adhesion Test KIT CC3000 contains a grip with cutter, a brush, an illuminated loupe and a roll of adhesive tape acc. EN ISO 2409.

Product Details:

"tqc" holland viscosity cups afnor

The tqc afnor viscosity cups are a range of titanium anodized aluminum viscosity cups. Laboratory type, to be used with stand, to measure the viscosity of lacquers, paint and other liquids.

 

• tqc afnor 2. 5 viscosity flow cup
• tqc afnor 4 viscosity flow cup
• tqc afnor 6 viscosity flow cup
• tqc afnor 8 viscosity flow cup

Product Details:

"tqc" holland film applicator for sag and levelling

the tqc sag and levelling film applicator is a special film applicator with dual function. One side with 10 gaps from 75 to 300 micron to test the tendency to sag in relation to the film thickness. At the counter side 5 pairs of notches of increasing depth are made to create sets of two film stripes. The merging of the stripes can be evaluated to define the leveling ability. The high-grade stainless steel will not be affected by acid or base elements.

Product Details:

NH300 Colorimeter

NH300 colorimeter are widely used in plastic, metal, electronic, paint, ink, textile, garment, printing and dyeing, food, medical, cosmetic, automotive, toy...industries.

Product Details:

This instrument enables accurate and reproducible prints and coatings to be made using a wide range of products, and many
different substrates. The different heads detailed over are fully and easily interchangeable, providing Gravure, Flexo and Meter Bar coating, giving exceptionally accurate surface coatings and laminations. The smallest differences in products can be detected
by applying multiple samples adjacent to each other

MAIN FEATURES
• Easily repeatable samples
• Interchangeable heads
• Multiple coatings simultaneously for comparison
• Maximum coating area 350 x 440mm (meter bar coating head)
• Coating speed 1 – 39m/min

GRAVURE PRINTING HEAD
K303 Standard Gravure Proofer is used in laboratories for quality control on all conventional ink/substrate
combinations for colour, printability, adhesion, etc.

Standard Design Gravure Plates:
303/D8W : 8 Wedges 150 lines/inch 100% - 60%
303/S3W : 3 Wedges 150 lines/inch
100% - 80% - 60%
Printing Area 275 x 285mm maximum.

FLEXO PRINTING HEAD
Utilises doctored anilox flexo plates from which the ink is transferred via the plate roller onto the substrate.
Photopolymer or rubber plates are made to your own design, including for instance company logo/address. Very
fine pressure adjustments can be made to obtain a perfect print on most substrates by the use of micrometers. This
also means that settings for any particular substrate can be recorded.

Standard Design Flexo Plates:
303/35 : 150 lines/inch @ 100%
303/25 : 150 lines/inch @ 60%
Printing Area 265 x 250mm maximum.

Product Details:

"TQC" Bird- Type Film Applicators 4- Sided

TQC Bird-type film applicator with flat edges. Four application sides for applying 4 different pre-defined thicknesses. The TQC Bird-type applicator is available in film width 50, 75 and 100mm and suitable for applying a host of different products onto flat and relatively solid substrates. The high-grade stainless steel will not be affected by acid or base elements.

We can give no guarantee of the wet thickness that will be obtained. The wet thickness is dependent upon the solids and vehicle content of the wet material as well as other factors. Film thickness deposited may vary from 40% to 80% of the actual gate clearance of the TQC Bird-type applicator.

Features:

• TQC Bird-type applicator 50mm, 50/100/150/200µm
• TQC Bird-type applicator 75mm, 50/100/150/200µm
• TQC Bird-type applicator 100mm, 50/100/150/200µm
• TQC Bird-type filmapplicator 60mm, gaps as desired Max. gap size: 3000µm
• TQC Bird-type film applicator, width 50mm, 4 gaps as desired Max. gap size: 3000µm
• TQC Bird-type film applicator, width 75mm, 4 gaps as desired Max. gap size: 3000µm
• TQC Bird-type film applicator, width 100mm, 4 gaps as desired Max. gap size 3000µm
• TQC Bird-type film applicator, width 80mm, 4 gaps as desired Max. gap size 3000µm
• TQC Bird-type filmapplicator width 150mm, gaps as desired Max. gap size: 3000µm
• TQC Bird-type filmapplicator width150mm, 50/100/150/200µm

Product Details:

Product Details:

"TQC" Pencil Hardness Test Acc. Wolff Wilborn Persoz And Koenig

The TQC Pencil Hardness Test according Wolff Wilborn provides in a simple method to test the scratch hardness of coatings. In this test, pencils in a range of 6B to 8H hardness-grade are used. The pencil is moved scratching over the surface under a 45° angle with a constant pressure. Then an optical assessment is carried out to see which pencil hardness damages the surface. Delivered with a set of 20 Koh-i-noor pencils and a pencil sharpener.

Product Details:

"TQC" HOLLAND VISCOSITY CUP ASTM D1200 FORD

The TQC Viscosity Cup ASTM D1200 Ford is a range of titanium anodized aluminum or stainless steel viscosity cups with fixed stainless steel nozzle (inner cavity). the viscosity cups are suitable for laboratory use with a stand. Widly used for measuring paint, lacquers and other liquids.

TQC Viscosity Cup ASTM D1200 Ford
Type: FB10 made of titanium anodised aluminum, with fixed nozzle orifice Ø 2 mm
Optional: possible to certify by calibration with certified oils

TQC Viscosity Cup ASTM D1200 Ford
Type: FB10 made of titanium anodised aluminum, with fixed nozzle orifice Ø 3 mm
Optional: possible to certify by calibration with certified oils

TQC Viscosity Cup ASTM D1200 Ford
Type: FB10 made of titanium anodised aluminum, with fixed nozzle orifice Ø 4 mm
Optional: possible to certify by calibration with certified oils

TQC Viscosity Cup ASTM D1200 Ford
Type: FB10 made of titanium anodised aluminum, with fixed nozzle orifice Ø 5 mm
Optional: possible to certify by calibration with certified oils

TQC Viscosity Cup ASTM D1200 Ford
Type: FR10 made of stainless steel, with fixed nozzle orifice Ø 1 mm
Optional: possible to certify by calibration with certified oils

Product Details:

"tTQC"IMPACT TEST – TUBULAR IMPACT

The TQC Impact Test is used to determine the impact resistivity and flexibility of coatings. The dual scale instrument is equipped with a special guidance which assures that the distance between each impact is always according to the standard. For correct positioning a spirit-level is built-in. Each Impact test comes as a complete set (instrument and accessoires) to perform a test according DIN/ISO 6272, ASTM D2794 and ASTM G14

Product Details:

"tqc" holland pressure density cup

Density or specific gravity (sg) is affected by entrapped air bubbles in the liquid under test. The tqc vf2095 sg-cup has a fixed internal volume of 100 ml. Which is to be compressed by the mechanism of the density cup.

After rotation, agitation or dispersion gas and air can be entrapped within the material. Under pressure the air will dissolve better into the liquid and any bubbles that are left undissolved will be compressed to a fraction of their original size. Density of the liquid is defined at a very high level of repeatability by weighing.

The tqc pressure density cup can easily be taken apart to allow easy cleaning.

Standards

 
en iso 2811-4. Look up the appropriate standard for a correct execution of the test. The test may only be carried out if all parts of the pressure density cup have an identic serial number.

Features:

• minimizes the effect of entrapped air bubbles
• high level of repeatability
• easy to clean scope of supply
• pressure density cup 100 ml
• desktop holder
• brush 25 mm and 40 mm
• calibration certificate

Product Details:

Dust Test Kit

The TQC Dust Test Kit according to ISO 8502-3 allows assessment of the quantity and size of dust particles on surfaces prepared for painting. Dust on blast cleaned surfaces can reduce coating adhesion, leading to premature coating failure and sub-standard coating finish. The dust test kit can be used in accordance with the recommendations of BS EN ISO 8502-3 either as a pass/fail test or as a permanent record of the presence of dust

Product Details:

"tqc" holland viscosity calibration oils

tqc viscosity calibration oils are manufactured in accordance with astm d 2162, the primary method for viscosity standards manufacture. They are fully traceable to national standards and are test equipment compatible. They are dual ukas certified to the international standards bs en iso / iec 17025 and iso guide 34.

 

• tqc viscosity calibration oil s6 500ml
• tqc viscosity calibration oil n10 500ml
• tqc viscosity calibration oil s20 500ml
• tqc viscosity calibration oil n26 500ml
• tqc viscosity calibration oil s60 500ml
• tqc viscosity calibration oil n100 500ml
• tqc viscosity calibration oil s200 500ml
• tqc viscosity calibration oil n350 500ml
• tqc viscosity calibration oil n415 500ml
• tqc viscosity calibration oil s600 500ml
• tqc viscosity calibration oil n1000 500ml
• tqc viscosity calibration oil s2000 500ml
• tqc viscosity calibration oil n4000 500ml
• tqc viscosity calibration oil s8000 500ml
• tqc viscosity calibration oil s30000 500ml

Product Details:

BGD 586 Portable Whiteness Meter has been developed by our company recently. It is designed with the demand of CIE, including standard light resource light environment. And it complies with GB2913, GB5950, GB8940.1, GB12097, GB13025.2 etc standards. It is used widely in the fields such as textiles printing and dyeing, paint and coating, chemical materials, paper and cardboard, plastics, white cement, ceramics, enamelware, porcelain clay, French white, maylum etc.

Features :

• Can be put in pocket because of microminiature size, portable and is convenient for testing flieldwork.
• With the newest repairing light resource system, and can measure the fluorescene whiteness
• Simple operation and no need to zero calibration
• Saving electrical power, it only needs one battery and can works excess of fifty hours continuously (can measure ten thousands data)
• Special technical design about moisture protection can ensure you use it in carious harsh environments.
• Long lifetime light source.
• Pass the standard value through the calibrated white board.
• Can select the case which put the powder sample in specially and pressing sample apparatus.