Salt Spray Corrosion and Climatic Testing Instruments

Product Details:

Erichsen , Germany make Corrosion Testing Apparatus, Model 606-Basic

• Test chamber in rectangular design, made of impact resistant eco-friendly polypropylene material,
• Integrated control unit,
• Manual dome opening,
• Closing pump for optimum setting for the salt solution to be sprayed
• Storage tank for approx. 125 l salt solution,
• The necessary regulating and control instruments for temperature monitoring in the test chamber, the temperature of the humidifier, the spray pressure and the duration of the test,
• 3 specimen holder for weathering panels.

 

The test apparatus ready for operation; design in accordance with technical Leaflet 606-Basic/E, to perform continuous corrosions tests in accordance with DIN EN ISO 9227, DIN EN ISO 6270-2, DIN 53 167, ASTM B 117, ASTM B 368 T "CASS TEST", DEF 1053 . 24, MIL-STD 202 B, PN X 41-002.

Additional Information:

• Item Code: 606-Basic

Product Details:

Cyclic corrosion testing provides the best possible laboratory simulation of natural atmospheric corrosion. Research indicates that cyclic corrosion testing results are similar to outdoor environments in resulting structure, morphology, and relative corrosion rates.

Q-FOG CRH cyclic corrosion chambers can perform traditional salt spray, Prohesion, and most cyclic automotive tests. They feature fully-adjustable relative humidity and precise control over ramp times. An optional shower function is also available. Q-FOG CRH chambers are available in two sizes to fulfill a wide range of testing requirements.

Q-FOG CRH cyclic corrosion testers are the simplest, most reliable, and easiest to use RH-controlled corrosion chambers available.

Product Details:

Cyclic corrosion testing provides the best possible laboratory simulation of natural atmospheric corrosion. Research indicates that test results are similar to outdoors in resulting structure, morphology, and relative corrosion rates.

Q-FOG cyclic corrosion chambers from Q-Lab can run traditional salt spray, Prohesion, and most cyclic automotive tests. Q-FOG chambers are available in two sizes to fulfill a wide range of testing requirements.

Q-FOG cyclic corrosion testers are the simplest, most reliable, and easiest to use corrosion testers available.

Product Details:

For over 50 years, Q-PANEL steel and aluminum test substrates have been recognized as the world standard for a consistent and uniform test surface for paints, plating, adhesives, sealants, rust inhibitors and other coatings.

Thousands of labs around the world use millions of our steel and aluminum test panels every year for color development, weathering exposures, salt spray and corrosion testing, physical properties testing and quality control. A wide range of panel sizes and types are available for immediate shipment from stock.

Look for the Q-shaped hole. Its our trademark and your assurance of quality.

Product Details:

The QUV accelerated weathering tester reproduces the damage caused by sunlight, rain and dew. In a few days or weeks, the QUV UV tester can reproduce the damage that occurs over months or years outdoors. To simulate outdoor weathering, the QUV accelerated tester exposes materials to alternating cycles of UV light and moisture at controlled, elevated temperatures. It simulates the effects of sunlight using special fluorescent UV lamps. It simulates dew and rain with condensing humidity and/or water spray. The QUV accelerated weathering tester is the simplest, most reliable, and easiest to use weathering tester available. With thousands of testers in use worldwide, it is the world's most widely used weathering tester.

Product Details:

The Q-SUN B02 rotating rack xenon arc chamber was designed specifically to meet the ISO 105 B02 standard for textile lightfastness testing. After more than half a decade of successful sales around the world, the B02 tester has been discontinued in favor of an even more flexible model, the Q-SUN Xe-2.

Product Details:

The Q-SUN Xe-3 xenon arc chamber reproduces the damage caused by full-spectrum sunlight and rain. In a few days or weeks, the Q-SUN tester can reproduce the damage that occurs over months or years outdoors.

The Q-SUN Xe-3 tester is a full-featured lightfastness, colorfastness, and photostability chamber at a breakthrough price. It utilizes three separate xenon lamps for a large capacity. The Q-SUN Xe-3 testers slide out specimen tray is 451mm x 718mm and is useful for exposing large, three-dimensional parts or components. The Xe-3 tester offers standard humidity control, and optional spray, back spray and chiller features.

The Q-SUN Xe-3 is the only xenon arc tester that also has an optional dual spray capability. This allows for a second liquid such as acid rain or soap solutions, to be sprayed onto test specimens.

The Q-SUN Xe-3 is the simplest, most reliable, and easiest to use full-sized xenon arc chamber available.

Product Details:

The Q-SUN Xe-2 rotating rack xenon arc test chamber reproduces the damage caused by full-spectrum sunlight and rain. In a few days or weeks, the Q-SUN Xe-2 tester can reproduce the damage that occurs over months or years outdoors.

The Xe-2 tester is a full-featured weathering, lightfastness and photostability chamber at a breakthrough price. It provides precise control of critical test parameters including spectrum, irradiance, relative humidity, chamber temperature and black panel/black standard temperature. Water spray is also an available option.

The versatile Q-SUN Xe-2 tester is the simplest, most reliable, and easiest to use rotating rack xenon arc tester available.

Product Details:

Characteristics:

• Ultraviolet aging tester is designed for convenience of end user. It’s easy to operate, safe and reliable.
• The thickness of specimen is adjustable and the specimen installation is fast and convenient.
• The door rotating up does not interfere with the operation and the tester takes very small space.
• Its unique condensation system can be contented by tap water.
• The heater is under the container rather than in the water, which is long life, easy to maintain.
• The water level controller is outside the box, easy to monitor.
• The machine has truckles, convenient to move.
• Computer programming is convenient, automatically alarming when incorrectly operated
• It has irradiance calibrator to extend the life of the lamp tube (more than 1600h).
• English instruction Manual, convenient to consult.
• Three Model available : common, light irradiance controlling, spraying type

Technical Parameter:

Confirming to ISO, ASTM, DIN, JIS, SAE, BS, ANSI standard specification.
The condensing device simulated the outdoor moisture influence, can achieve 100% R.H.
Electronic irradiance control system
Use the blackboard temperature sensor measuring temperature accurate, repeatable test results.
Humidity, condensation, water spray circulating consecutive testing.
Intensity of illumination has CR-10 calibrating pegging and automatic calibration procedures (American Q-the Lab patent technology) .

Product Details:

Relevant standards requirement

1. Test Object: battery pack andsystem.
2. Refer GB/T4 part 5.5.2 test method, test according to GT/T2423.17 test conditions.
3. The salt solution was made up with sodium chloride (chemically pure and analytically pure) and distilled or deionized water???Its concentration is (5 + 1)% (mass fraction).
4. (35 +-2) ???, the measured pH value is between 6.5-7.2.
5. Placed the test objects in the salt spray chamber for cycling test. Each cycling duration for 24h. Spray salt solution to the test object for 8 hours under the temperature of (35+- 2) ??? , remain for 16 hours. Between the forth and the fifth hour in one cycles should be according to test requirement in GB/T 28046.1-2011, test mode with 3.2.
6. Total 6 cycles testing.
7. Salt spray test is not necessary for the test objects being installed in passenger, luggage or cargo compartments.

Product Details:

Compact enough for a laboratory bench top, but durable enough for production, the Hot Roll Laminator can consistently reproduce hot laminate product samples that are ready for testing or small-scale production. With flexible controls, the Hot Roll Laminator allows for a wide range of materials to be laminated including papers, films, foils and many other materials. The heated laminating system is designed to be very versatile and can be modified for a multitude of variations.

• Rugged construction, capable of withstanding the abuse of the production environment
• Produce laminated samples of unlimited length up to 18" (45 cm) in width
• Variable speed motor allows the following laminating speeds:
• Top and bottom rolls are 4" (10 cm) diameter by 18 1/2" (47 cm) face width
• Top roll is heated by a 1500-watt heating rod inserted through the full width of the roll axis
• Capable of maintaining temperatures up to 400°F (204°C)
• J-type thermocouple is an integral part of the heating rod
• Heating rod designed with a 35-30-35 heating profile to more evenly distribute heat across width
• Roll temperature is accurately maintained by a digital PID controller
• Controller is capable of maintaining temperatures to a tolerance of ± 2°F (1°C)
• Choose top roll material from: Aluminum, Hard coat anodized with Teflon coating, Steel, chrome plated and precision ground to 8 RMS
• Bottom roll material is aluminum and covered with 80 durometer silicone rubber
• Bottom roll is driven, top roll idles
• Digital speed control with improved stepper motor technology
• Requires compressed air - max pressure 90 PSI (6 bar)
• Air pressure is adjustable for differing levels of laminating pressure
• Laminating pressure (LP) can be approximated using the following formula: LP = (6.28 x line pressure) / sample width
• Flow controls are included on both laminator cylinders to allow for smooth, safe operation
• Unwind stand is capable of holding roll stock up to 12" (30 cm) diameter by 18" wide (45 cm)
• Length of lamination can be measured
• Digital controls to control speed, unit of measure and jog functions
• Operating temperature range 32 – 122 °F (0-50°C)
• Standard input voltage - 120 VAC (50/60 Hz)
• 2 – 300 IPM, 0.1 IPM increments from 2-12 IPM, 0.5 IPM increments from 12-200 IPM
• 5 – 750 CPM, 0.25 CPM increments from 5-30CIPM, 1.25 CPM increments from 30-750 CPM

Accessories :

• Gap adjustment
• 3" core chuck with friction brake
• Dual unwind
• Manual windup station
• Release paper (roll)
• Polyester (roll)

Additional Information:

• Item Code: HL-100-101

Product Details:

Soluble Salt Tester for measuring the concentration of soluble salts on metal surfaces

Measures the concentration of soluble salts (salt contamination) on metal surfaces in accordance with ISO 8502-6, 8502-9.
Conductivity probe specifically designed for ISO 8502-6, 9

Displays test duration, sample temperature, conductivity (µS/cm) and surface density (mg/m2 or µg/cm2)
Easy 1-2-3 gage interface guides users through the Bresle test method
Automatic storage of a background (blank) measurement — handy when performing multiple tests
PosiTector interchangeable platform – attach any PosiTector probe to a single gage body
USB, WiFi, and Bluetooth connectivity to PosiSoft PC, Mac, and Smartphone software
Certificate of Calibration showing traceability to NIST included (Long Form)

Conforms to ISO 8502-6/8502-9, US Navy NSI 009-32, US Navy PPI 63101-000, AS 3894.6, IMO MSC.215(82), IMO MSC.244(83), SSPC Guide 15, ISO 11127-6, ASTM D4940

Product Details:

Soluble Salt Tester for measuring the concentration of soluble salt on metal surfaces

Measures the concentration of soluble salts (salt contamination) on metal surfaces in accordance with ISO 8502-6, 8502-9.

-Conductivity probe specifically designed for ISO 8502-6, 9
-Displays test duration, sample temperature, conductivity (µS/cm) and surface density (mg/m2 or µg/cm2)
-Easy 1-2-3 gage interface guides users through the Bresle test method
-Automatic storage of a background (blank) measurement — handy when performing multiple tests
-PosiTector interchangeable platform – attach any PosiTector probe to a single gage body
-USB, WiFi, and Bluetooth connectivity to PosiSoft PC, Mac, and Smartphone software

Product Details:

For over 50 years, Q-PANEL test substrates have been recognized as the world standard for a consistent and uniform test surface for paints, plating, adhesives, sealants, rust inhibitors and other coatings. This consistency and uniformity is now available through Q-Labs CX-series corrosion test coupons.

Corrosion test coupons ensure repeatability and reproducibility when performing laboratory corrosion testing. They help a user independently monitor the test conditions in the chamber, by measuring the mass loss of the coupons as the test progresses. CX corrosion coupons are designed to meet the stringent requirements specified in modern corrosion test methods, such as GMW14872, GM9540P, SAE J2334, SAE J2721, ASTM B117, ISO 9227, and VDA-233-102.

All Q-PANEL CX-series corrosion coupons include Certificate of Analysis, come pre-cleaned and ready to use right out of the package. This allows the user to simply measure the panels and place them in the tester, saving time and effort. And best of all, CX corrosion coupons are often half the price of competitors coupons.